Eccentric (mechanism) In mechanical engineering, an eccentric is a circular disk ( eccentric sheave) solidly fixed to a rotating axle with its centre offset from that of the axle (hence the word " eccentric ", out of the centre). It is used most often in steam engines, and used to convert rotary motion into linear reciproing motion to drive ...

Working Principle of Hotchkiss Drive: The parts which are presented above constitute the Hotchkiss drive. The power generated at the engine is to be transmitted to the Gearbox and from there it is transmitted to the rear axle casing via propeller shaft.

Parts in clutch :. The clutch assembly consists of many small parts but following are the major parts. 1. Flywheel – The flywheel, mounted on the crankshaft, keeps on running as long as the engine keeps running. The flywheel is equipped with friction surface OR .

The IRON MAN Windmill™ is a modern version of the Traditional American Water Pumping Windmill. This legendary machine has dependably provided significant amounts of water, serving the needs of farms, families and communities with only minimal attention for over 150 years. First designed in the mid 1800's, the traditional American windmill has ...

Feb 24, 2012 · Working of Wind Turbine. When the wind strikes the rotor blades, blades start rotating. The turbine rotor is connected to a highspeed gearbox. Gearbox transforms the rotor rotation from low speed to high speed. The highspeed shaft from the gearbox is coupled with the rotor of the generator and hence the electrical generator runs at a higher ...

Working of Sliding Mesh Gearbox: The Sliding Mesh Gear box uses Spur Gears for the transmission of power from the engine shaft to the main shaft. It generally consists of 3 shafts Clutch shaft, Lay shaft and Main Shaft whose explanation was given above. It is a transmission mechanism of Just 4 gears and out of these 4, one is the reverse gear.

May 13, 2021 · All jet engines, which are also called gas turbines, work on the same principle. The engine sucks air in at the front with a fan. A compressor raises the pressure of the air. The compressor is made with many blades attached to a shaft. The blades spin at high speed and compress or squeeze the air.

Feb 11, 2013 · Working Principles and Operation. The underlying principles for the working of a BLDC motor are the same as for a brushed DC motor;, internal shaft position feedback. In case of a brushed DC motor, feedback is implemented using a mechanical commutator and brushes. With a in BLDC motor, it is achieved using multiple feedback sensors.

Oct 03, 2020 · The DC motor working principle is that a currentcarrying conductor experiences a mechanical force when placed in a magnetic field. This is known as the Lorentz force. And the direction of this force is given by FLEMING'S LEFTHAND RULE. DC motor working principle is similar to the working principle of a DC generator.

Mar 24, 2015 · The lift is a type of vertical transport equipment that efficiently moves people or goods between floors (levels, decks) of a building, vessel or other structure. generally powered by electric motors that either drive cables, hoist, or pump hydraulic fluid to raise a cylindrical piston like a jack. 4. Basic terminologies..

Jul 19, 2021 · Working principle and structure of double shaft shredder: working principle. The doubleshaft shredder is driven by an electric motor or a hydraulic motor. The cutters are made of special alloy steel and are controlled by a programmable logic controller. It can automatically reverse when encountering hard objects.

Feb 09, 2017 · The shafts connected straight. In the first case, the input and output shaft are connected in a straight line. In this case, motion is really simple. The input shaft will turn the cross, and the cross will turn the output shaft. It is clear that both the input and output shafts will turn at the same speed. Fig:3 Universal joint under a straight ...

How Magnetic Drive Pumps Work. It is the attraction of the drive magnet and the impeller magnet which allows the full torque of the motor to be passed onto the impeller. As the shaft of the motor does not extend into the interior of the pump, there is no need for a shaft seal. As the impeller is not fixed to the motor shaft, the impeller floats ...

The working principle is illustrated in fig. 1519. The stator which encloses the rotor both of which are provided with rings of blades. ... The two shafts are connected together by means of gears of equal size. The two rotors revolve at the same speed. It works just like the gear pump where the mixture at the outlet side is at a high pressure.

Apr 30, 2009 · The same principle is used on board to generate electricity. The alternator can be attached to an auxiliary engine or can even be attached to the main engine or the propeller shaft. Construction. The main parts of an alternator are a stator and a rotor. The arrangement can be of two types.

Mar 26, 2019 · Figure 1: Working Principle of Centrifuge. ... For the minimizing of vibration and strain on the shaft and bearings, a loaded rotor should be well balanced,, its total mass should be distributed about the axis of rotation such that the resultant of all elemental forces is zero.

What is the working principle of engine balance shaft? When the engine is in the working state, the piston movement speed is very fast, and the speed is very uneven. When the piston is at the top and bottom dead center, its speed is zero, but the speed in the middle of .